Boca Research Adjustable MC Ghost Manual de usuario

Users Manual Adjustable MC Ghost Ticket PrinterAdjustable MC Ghost Ticket Printer

Figure 4 - Micro Ghost - rear viewFigure 5 - Micro Ghost - top view withelectronics exposed4Roll Stock HolderMain Logic Board AC connectorOn/Off switc

4.0 InstallationThe Adjustable MC Ghost ticket printer is designed to be mounted on a desktop or ona shelf. Prior to the site preparation and installa

5.0 ConfigurationThe Adjustable MC Ghost is factory configured for a variety of customer requirements.1. The printer has a resolution of 200dpi.2. The

6.0 Standard Interface Pinouts6.1 Serial PinoutsRS232 (Standard)Pin Function2 Printer Transmit3 Printer Receive7 Ground5,20 DTR (Printer Ready)4,22 RT

7.0 Thermal Paper - Theory & SpecificationThe print head’s life expectancy is composed of both a mechanical and an electrical component.Both of th

8.0 Maintenance and AdjustmentsYour ticket printer is solidly constructed and has been designed for high volume use.It requires minimal care to prov

The position of the tear can be controlled by changing the cut count setting in theOPERATOR MENU (see Appendix A). If you are not able get the desired

8.1.6 THERMAL PRINT HEADThe print head should be cleaned monthly, initially, to prevent debris from building upon the print element. The required clea

Figure 9a - Print Head removalFigure 9b - Print Head removalFigure 9c - Print Head removal12

8.1.7 Rubber Drive Roller (Platen)The rubber drive roller should be cleaned once a year to prevent paper dust frombuilding up on the roller. Clean dri

BOCA SYSTEMS, INC.©1999 Boca Systems, Inc. All rights reserved.Under the copyright laws, this manual may not be copied, in whole or in part, withoutth

9.0 Spare Parts ListDESCRIPTION PART NUMBERAC Switch and power filter P31-1000Belt, Timing 100T (200 dpi) P50-1011Control Panel Assembly, FGL41 421671

10.0 Troubleshooting Guide This is a simplified troubleshooting guide listing some of the typical problems. It is not intendedto provide technical de

5. ERRACTIC PRINT POSITIONa. See # 46. POOR PRINT OUT (light print out)a. Make sure the print head/cam lock assembly if fully locked in the closed pos

Appendix A - Operator Menu Options This printer allows the user to adjust various printer options through the control panel.To access and use the OP

The chart below lists the present menu topics.These topics are subject to change.OPERATOR MENU!BAUD RATE?MINI/MICRO?PRINT SPEED?DIAGNOSTIC MODE?TICKET

MINI/MICRO?Defines the type of printer.MINIIs for a printer with a Silent Cutter Assembly (SC2) ( Mini, Mini Plus, Mini MB, Dual Mini)MICROIs for a pr

PAPER MODE?Is generally used only for test purposes. It may also be used on roll stock with noblack marks on the ticket.Your choices are YES (Enabled)

JUST EXIT?Will exit the menu options without saving any changes.If you with to exit without saving the new value then press TEST, if not press MENU.To

Table of Contents Page1.0 Introduction 12.0 Unpacking the Printer 23.0 A tour of your printer 3-44.0 Installation 55.0 Configuration 66.0 Standard Int

Table of Figures and Appendices PageFigure 1 Packaging 2Figure 2 Micro Ghost Ticket Printer 3Figure 3 Side view with door open 3Figure 4 Rear view 4F

FCC NOTICENOTE: The equipment has been tested and found to comply with the limits for a classA digital device, pursuant to part 15 of the FCC rules. T

WARRANTY INFORMATIONPRINTERS - BOCA warrants each printer to be free of defects for a period of one yearfrom the date of shipment when subject to norm

1.0 IntroductionThe BOCA Adjustable MC Ghost is a direct thermal ticket printer especially designedfor airline boarding pass and bagtag applications.

2.0 Unpacking the PrinterThe printer is shipped in a ruggedized container. Please save packing material forfuture use. Remove the printer (see figure

3.0 A Tour of Your PrinterFigure 2 - Micro Ghost ticket printerFigure 3 - Micro Ghost ticket printer3ticket output slotcontrol panelAdjustment KnobTim